START A PETITION 25,136,189 members: the world's largest community for good
START A PETITION
x

Salvage Style: Old Wooden Shutter CD Rack

Salvage Style: Old Wooden Shutter CD Rack

The authors of Salvage Style know from personal experience that this shutter CD rack is a good idea because it has their teenager’s seal of approval. Teenagers usually buy CDs more frequently than the rest of us, and as a collection of CDs expands, storage can become a problem.

Of the innumerable CD storage systems that are commercially available, most take up valuable surface space, and few can be described as well-designed. If, however, you are re able to find an old wooden louvered shutter, we are sure you will agree that, once wall mounted at eye level with the CD titles on view, it provides an ideal storage solution.

When selecting an old wooden shutter for conversion into a CD rack, make sure to measure the width of the slats and their distance apart to ensure that the finished rack will comfortably hold boxed CDs. If you wish, you can use the shutter in its original condition and not repaint it, but if you want it to fit into an existing interior decorating scheme, it is probably best to paint it in the color or colors of your choice.

EQUIPMENT
Screwdriver
Electric sander
Sandpaper
1 1/2-inch paintbrush
soft cotton rags
Electric hammer drill
Masonry drill bit

MATERIALS
Old wooden louvered shutter
Wood filler (if necessary)
Two contrasting colors matte acrylic paint (low VOC, less toxic brand)
Hardboard or thin plywood to fit the back of the shutter
Matte black acrylic paint (low VOC, least toxic brand)
Small wood screws
Two mirrors
Rawlplugs
Screws to fit mirrors

METHOD
Editor’s note: Be very careful of scraping paint off old shutters, as the paint could contain lead. Wear a mask, and work outside.

1. Remove any hinges or other metal hardware, sand down any flaked and loose paint from the shutter, and fill any holes or damage with wood filler, wait for the filler to set, and then sand it down to match the surrounding wood. Sand the entire shutter to provide a smooth surface for the new paint. It is not necessary to remove all the old paint, but pay particular attention to revealing the underlying wood on the edges of the frame and slats, where natural wear would occur.

2. When you are satisfied with the finish, paint the shutter frame in the darker of your selected colors of matte acrylic paint and let them dry.

3. When the shutter is completely dry, sand through the surface of the paint to reveal the underlying wood on all the outside edges of the frame and the exposed edges of the slats. You can either use an electric sander or, for a more subtle effect, sand by hand. The sanding is designed to simulate natural wear; if you do make a mistake, it is very simple to repaint and start again.

4. When the shutter frame looks suitably distressed, clean off any dust without he cotton rag and apply two coats of the satin finish interior wood varnish to the entire shutter, letting it dry between coats.

Cut the sheet of hardboard or thin plywood to fit approximately 1/2 inch inside the back of the shutter. Paint one side of the hardboard or thin plywood with the matte black acrylic paint and, when dry, attach it to the back of the shutter with the small wood screws. Fit two mirror hangers to the rear of the shutter and decide where you want to hang it. Drill the holes and insert rawplugs before screwing the DC rack to the wall.

Read more: Home, Reduce, Recycle & Reuse

Adapted from Salvage Style In Your Home, by Moira and Nicholas Hankinson. Copyright (c) 2000 Rodale Inc. Reprinted by permission of Rodale, Inc.
Adapted from Salvage Style In Your Home, by Moira and Nicholas Hankinson.

have you shared this story yet?

go ahead, give it a little love

Annie B. Bond

Annie is a renowned expert in non-toxic and green living. She was named one of the top 20 environmental leaders by Body and Soul Magazine and "the foremost expert on green living." - Body & Soul Magazine, 2009. Learn Annie's latest eco-friendly news on anniebbond.com, a website dedicated to healthy and green living.

2 comments

+ add your own
12:40AM PDT on Jul 24, 2010

TY Dearest. Thank you Jessica for the link!

8:15AM PST on Dec 2, 2008

You could paint it with a NO VOC Acrylic Paint or Stain and cover it with a No VOC Varnish to match any room! Make sure the paints are NO VOC and non toxic. A great place for these products is at www.earthsafefinishes.com. I just refinishes a dresser with their stain and varnish. No smell, no VOC's! Company is called Earth Safe Finishes.

add your comment



Disclaimer: The views expressed above are solely those of the author and may not reflect those of
Care2, Inc., its employees or advertisers.

people are talking

Waste vodka using it a cleaning product? No way! That's what vinegar is for.

Hello am Jeniffer from UK i wanna thank Prophet suleman for what he has done for me at first i taugh…

CONTACT THE EDITORS



Select names from your address book   |   Help
   

We hate spam. We do not sell or share the email addresses you provide.